 Electrostatics Home | CATV Home | EAS Home | Contact Us | Site Map | About Monroe |
||
 Timers Switches Distribution Amplifiers Remote Controls DTMF Encoders / Decoders Enclosures Circuit Boards Press Releases Application Notes Manuals for Obsolete Products Representatives |
Remote Controls |
|
 |
R190A LAN Hub Controller Monroe Electronics’ Model R-190A supplies remote contact losure from any web browser. This allows the operator to perform remote functions at remote sites with contact closures. LAN IP addresses may be assigned to the R190A from any PC, using a web browser. Data Sheet PDF |
|
 |
6002 Remote Control The Monroe Electronics Model 6002 is a telephone remote control system capable of answering telephone calls and giving the calling party control of six relays. It provides the ability to interrogate six status input points for remote control and status monitoring of unattended sites. Monroe Model 3405 Expansion Board is used to expand the inputs and outputs of the 6002 from 6 to 12 each. Data Sheet PDF |
|
 |
6003 Remote Control The Monroe Electronics Model 6003 is a remote control system capable of giving the operator control of six remote control relays. It allows the user to interrogate six logic input points for remote control and status monitoring of unattended sites. Monroe Model 3405 Expansion Board is used to expand the inputs and outputs of the 6003 from 6 to 12. Data Sheet PDF To Top of Page |
|
 |
3405 Expansion Board Monroe Model 3405 Expansion Board is used with the Model 6002 and 6003 Remote Controls expanding the inputs and outputs of these units from 6 each to 12 each. The 3405 includes all necessary connectors, wiring, firmware and installation instructions to enable the user to install the unit in the field. No special tooling is required. Data Sheet PDF Manual PDF To Top of Page |
|
 |
948A Cue Tone Controlled A/V & IF/RF Switch Monroe Electronics’ Model 948A Cue Tone Receiver decodes Cue Tone signals transmitted by satellite and microwave program services to provided unattended audio/video switching. The Model 948A is capable of accepting a sequence up to four dual tone signals and responds by energizing it’s audio/video 2x1 switch. The Model 948A contains a telephone answering device and is compatible with standard Touch-Tone® enabling it to be adapted to many remote control applications. The Model 948A monitors an audio signal, looking for a specific code sequence to which it has been programmed to respond. When the complete programmed ON code sequence is received the audio/video switch will energize. The switch remains energized until the programmed OFF code sequence is received, de-energizing the audio/video switch. The telephone override feature permits remote control of the 948A’s audio/video switch via Touch-Tone®. The 948A will answer the incoming signal, selectable on 1 - 9 rings, and complete an audio path to the decoder card. The calling party then enters the programmed ON or OFF four digit sequence to energize or de-energize the audio/video switch. An internal timer can be set to disconnect the 948A from the telephone line after 30 seconds, and is field adjustable from 6 - 135 seconds. Data Sheet PDF Manual PDF To Top of Page |
|
 |
948AX Cue Tone Controlled A/V & IF/RF Switch Monroe Model 948AX Cue Tone Receiver decodes Cue Tone signals transmitted by satellite and microwave program services, to provide unattended audio/video switching. The Model 948AX is capable of accepting a sequence up to four DTMF® signals. The Model 948AX monitors an audio signal, looking for a specific code sequence to which it has been programmed to respond. When the complete programmed ON code sequence is received the audio/video switch will activate. The switch will remain activated until the programmed OFF code sequence is received, deactivating the audio/video switch. Data Sheet PDF Manual PDF To Top of Page |
|
| Monroe
Electronics Inc., 100 Housel Avenue, Lyndonville,
NY 14098 phone:1-585-765-2254 fax:1-585-765-9330 Copyright © 1999-2007 Monroe Electronics, Inc. |
||
 |
|
|